MacDon M200 Betreibershandbuch

Double Windrow Attachment For M150 & M200 TractorsSET-UP INSTRUCTION / OPERATOR’S MANUAL / PARTS CATALOGJanuary, 2009Part #169216 $15

SET-UP INSTRUCTIONS Form 169216 January 2009 8 25. Align the deck pivot with holes in clevis by raising or lowering the floor jack and insert shaf

SET-UP INSTRUCTIONS Form 169216 January 2009 9Hydraulics Installation HYDRAULICS OVERVIEW See following pages

SET-UP INSTRUCTIONS Form 169216 January 2009 10Hydraulics Installation (continued) 29. .Install #10 ORB X #10 JIC elbow (A) in port “DWA” on drap

SET-UP INSTRUCTIONS Form 169216 January 2009 11 34. On D60 headers without reverser kit, connect case drain hose (G) to “T” port on the header dri

SET-UP INSTRUCTIONS Form 169216 January 2009 1236. Remove plugs (L) and (M) from the lift manifold block and retain. 37. Install auxiliary valve b

SET-UP INSTRUCTIONS Form 169216 January 2009 1343. Cut hole in decal and install rotary switch (C) as shown. The hole is already present in the mo

SET-UP INSTRUCTIONS Form 169216 January 2009 14 49. The program in the tractor monitor needs to be changed to recognize the DWA. a. Turn the ke

OPERATION Form 169216 January 2009 15 CAUTION: To avoid bodily injury: 1. Review the safety sections of your tractor and header Operator’s Manua

OPERATION Form 169216 January 2009 16 To adjust deck angle: The deck angle relative to the right hand drive tire is adjustable with turnbuckle (Q

OPERATION Form 169216 January 2009 17To adjust deck height: The deck should never touch the ground or excessive wear could occur to some deck com

MACDON DOUBLE WINDROW ATTACHMENT

OPERATION Form 169216 January 2009 18Conditioner Forming Shield Position: Make sure forming shield is high enough to clear the deck when it is lo

OPERATION Form 169216 January 2009 19 Operating Recommendations: 15’, 16’, 18’, 20’ Headers: On the first pass, the side delivery system is raise

MAINTENANCE/SERVICE Form 169216 January 2009 20Draper Tension Adjustment: Draper tension should be just enough to prevent slipping and keep drape

MAINTENANCE/SERVICE Form 169216 January 2009 21DANGER To avoid bodily injury or death from unexpected start-up or fall of raised machine, stop eng

MAINTENANCE/SERVICE Form 169216 January 2009 22Draper Roller Maintenance: The draper rollers have non-greaseable bearings. The external seal sho

MAINTENANCE/SERVICE Form 169216 January 2009 23C B ADraper Roller Bearing/Seal Replacement: 1. Remove roller assembly. See previous section for

MAINTENANCE/SERVICE Form 169216 January 2009 24Hydraulic Schematic

REPAIR PARTS Form 169216 January 2009 25A TABLE OF CONTENTS Deck, Draper & Rollers ...

Form 169216 January 2009 2634324635134636326503633253563495962535456155275413752756DECK, DRAPER & ROLLERS (Illustration 1)

Form 169216 January 2009 27DECK, DRAPER & ROLLERS REF PART NUMBER DESCRIPTION QTY SERIAL NUMBER 1 172730 DECK – complete with decal

Form 169216 January 2009 1MacDon M Series Windrower Tractor DOUBLE WINDROW ATTACHMENT TABLE OF CONTENTS Introduction...

Form 169216 January 2009 28DECK, DRAPER & ROLLERS (Illustration 2)

Form 169216 January 2009 29DECK, DRAPER & ROLLERS REF PART NUMBER DESCRIPTION QTY SERIAL NUMBER 7 144833 ROLLER – idler weldment...

Form 169216 January 2009 30DECK SUPPORTS & LINKAGE (Illustration 1)

Form 169216 January 2009 31DECK SUPPORTS & LINKAGE REF PART NUMBER DESCRIPTION QTY SERIAL NUMBER 4 172746 ARM – decal assembly...

Form 169216 January 2009 32DECK SUPPORTS & LINKAGE (Illustration 2)

Form 169216 January 2009 33DECK SUPPORTS & LINKAGE REF PART NUMBER DESCRIPTION QTY SERIAL NUMBER 1 144590 SUPPORT WELDMENT KIT, consist

Form 169216 January 2009 34HYDRAULICS & IN-CAB ELECTRICAL

Form 169216 January 2009 35HYDRAULICS & IN-CAB ELECTRICAL REF PART NUMBER DESCRIPTION QTY SERIAL NUMBER 1 163694 MANIFOLD-DWA DRIVE, se

Form 169216 January 2009 36HYDRAULIC SERVICE COMPONENTS

Form 169216 January 2009 37HYDRAULIC SERVICE COMPONENTS REF PART NUMBER DESCRIPTION QTY SERIAL NUMBER 1 163694 MANIFOLD-DWA DRIVE ...

SET-UP INSTRUCTIONS Form 169216 January 2009 2NOTE: This unit fits only the tractor models listed on page 1. It can not be installed on the M100 t

Form 169216 January 2009 38DECALS REF PART NUMBER DESCRIPTION QTY SERIAL NUMBER 1 172701 DECAL – draper/auger position...

NUMERICAL LIST PART NO. PAGE PART NO. PAGE PART NO. PAGE PART NO. PAGE Form 169216 January 2009 392147 33 7663 27 10948 35 11695 29 14338 27 1

SET-UP INSTRUCTIONS Form 169216 January 2009 3Draper Drive Block Installation 1. Move the left cab-forward platform to the open position for acc

SET-UP INSTRUCTIONS Form 169216 January 2009 45. Remove hose (E) from cooler by-pass relief valve next to oil filter and connect to fitting (B) o

SET-UP INSTRUCTIONS Form 169216 January 2009 5Linkage Installation 9. Remove support (A) by removing nut (B). 10. Locate in hardware kit two car

SET-UP INSTRUCTIONS Form 169216 January 2009 6 14. M200: Remove four bolts (D) from the front engine mounts, two on left side and two on right si

SET-UP INSTRUCTIONS Form 169216 January 2009 718. Cylinder pivot must be in the lower hole (shown) for A30/40 or D60 headers and upper hole for R8